Process position before model
The same equipment family can serve pre-selection, concentration, cleaning, scavenging or tailings recovery depending on its location in the flow sheet.
Dry Drum Magnetic Separator
The Dry Drum Magnetic Separator is used in a dry material flow where magnetic response is used to split a feed into defined fractions or remove ferromagnetic contamination. Its outcome depends on the material trajectory over the drum, feed consistency, particle size, moisture and the process target rather than on a catalogue claim alone.
- Process position before model
- Feed condition controls the design
- Target stream is defined
- Testing may be required
- Process role
- Pre-concentration, recovery or magnetic impurity removal
- Feed state
- Dry bulk or slurry, depending on the equipment
- Separation basis
- Magnetic response and process flow
- Selection starts with
- Mineral, particle size, feed condition and target
Product role
Overview and how it fits the process
The Dry Drum Magnetic Separator is used in a dry material flow where magnetic response is used to split a feed into defined fractions or remove ferromagnetic contamination. Its outcome depends on the material trajectory over the drum, feed consistency, particle size, moisture and the process target rather than on a catalogue claim alone.
It may be reviewed for mineral pre-concentration, dry bulk purification or a prepared recycling stream. The project should identify the feed preparation, the intended magnetic and non-magnetic outlets, the required capacity and how the equipment integrates with the upstream conveyor or feeder.
Selection logic
Why this configuration needs site information
Feed condition controls the design
Particle size, liberation, moisture or slurry condition and feed consistency are reviewed before a configuration is proposed.
Target stream is defined
The selection discussion distinguishes the magnetic product, non-magnetic product and the downstream stage that receives each stream.
Testing may be required
Where mineral behavior is uncertain, representative material and process information should be reviewed before commitments are made.
Process position
Where it fits in a typical material flow
The diagram is a planning aid. Final positioning is confirmed from the line layout and the material duty.
- 01Prepared feed
- 02Magnetic separation stage
- 03Magnetic product stream
- 04Non-magnetic or tailings stream
- 05Downstream recovery or processing
Applications
Typical materials and industry contexts
Technical information
Technical specifications and confirmation basis
Published model references are shown where available. Final technical details are confirmed from current product records, material and site conditions.
ParameterPublished recordSelection confirmation
Model designationAvailable on requestTo be confirmed based on material and site conditions.
Process dutyAvailable on requestTo be confirmed based on material and site conditions.
Feed sizeAvailable on requestTo be confirmed based on material and site conditions.
Feed conditionAvailable on requestTo be confirmed based on material and site conditions.
ThroughputAvailable on requestTo be confirmed based on material and site conditions.
Magnetic product directionAvailable on requestTo be confirmed based on material and site conditions.
Non-magnetic product directionAvailable on requestTo be confirmed based on material and site conditions.
Water or slurry requirement where applicableAvailable on requestTo be confirmed based on material and site conditions.
Selection checklist
What to send for an initial configuration review
- State whether the objective is recovery, upgrading, cleaning or tramp iron removal.
- For wet circuits, describe the slurry condition and available water or process constraints.
- Share laboratory, plant or sample information when available.
Important boundary
- No recovery or grade claim is made without representative material and process evidence.
- Magnetic separation does not replace required crushing, screening, classification or other upstream preparation stages.
Send the process details with the product pre-selected in the inquiry form.
Start product inquiryProcess equipment
Related products for the same process line
Magnetic Separation EquipmentBelt High-Gradient Magnetic Separator
View product
Magnetic Separation EquipmentDisc Magnetic Separator for Tailing
View product
Magnetic Separation EquipmentWet Drum Magnetic Separator
View product
Magnetic Separation EquipmentCTN wet full countercurrent magnetic separator
View product
Magnetic Separation EquipmentCTS type wet co current magnetic separator
View productProduct FAQ
Questions to resolve before ordering
How is a mineral magnetic separator selected?
Selection begins with the mineral, particle size, feed condition, desired magnetic and non-magnetic product streams, throughput and the place of the machine in the process flow.
Can one separator solve every ore separation problem?
No. Magnetic response, liberation, feed preparation and separation target vary by material. A dry, wet, high-gradient or drum configuration is selected for the actual duty.
What should be sent for an initial technical review?
Provide mineral name, feed size, moisture or slurry condition, throughput, process sketch, desired product streams and any available test or plant data.
Are recovery results guaranteed from a catalog page?
No. Recovery depends on the material and process. Results should only be discussed after the feed and operating conditions are reviewed.
Request a quote
Share the operating conditions for Dry Drum Magnetic Separator
Your inquiry is tagged with this product page, product family, language, referrer and campaign data for the COWIN MAGNET team.